2005 Toyota Avensis mass air flow sinsor

If you have a trouble code indicating the mass sensor is faulty, you need to have it checked and replaced if necessary. It could be the wiring that are at fault. Check for loose or corroded connections,

???? ???? ??? ? ???? ?? ???? ?????? ??? ???? ????? ???? ??? ????? ?????:
?? ????? ???? ???? ?????????????? ??????? ??? ?? ????? ????? ????? ?????? ??????? ???? ??
????????????? ????? ???? ?? 3 ???? ?????? ? ???? ??? ???????????????? ?? ????? ??? ??22204-0j010/ MB197400-3010
? ???? ??? ????? ???? ???? ? ????? ???? ????????? ???? ?? ??? ??? ?? ?? ??? ????? ????? ???? ??????? ??? ???????? ?? ????? ????? 1zz?? ??? ???? ? ??? ???? ??
I bought an avinsis car with 1AZ engine from Germany now we have trouble with mass air flow sensor and the sensor number is 22204-0j010/MB197400-3010 so can we change another sensor to my car?
for example: can we change the 1ZZ mass air flow sensor to 1AZ car ?

Mass sensors are non interchangeable for most cases.

Thank you so much for your kind reply and help

You're welcome.

Dear respected sir/ madam,
Wish you be healthy and fine,
I a mechanic and always confront with troubles, so i kindly request you to kindly send me you Skype, so by your Skype i could solve my technical problems

i am from Afghanistan and English language is second language so by text i can not explain my problems
Thanks for your kind support

Dear sir/ madam,
wish you be fine and healthy
if we replace Nissan ECU, so what should we do??
please kindly explain it in details

also we need general and important information regarding Nissan cars engines and other cars engines
Thank you in advance

Dear sir/madam,
May you be healthy,
this is the car details:
Nissan skyline, gasoline, direct injector ,six cylinder, engine VQ25 (DD)
we went to this work support section and then we press enter
and the following text appeared
fuel pump will stop by touching start in idling crank a few times after engine stall
condition setting
fuel pump relay : off
so the main problem is that when we start the car and the engine speed does not go on from 1000 R/PM and the car become off
so what should we do ?
and we checked the car by carman scan lite
please kindly explain it in details
Thank you in advance

I am not sure I understand your question so I am making a guess.

After replacing of ECU, there is nothing you need to do except to start the vehicle and everything should be good. If the engine stalls , it is usually due to a dirty throttle body. Have it cleaned and retest. If your scan tool has a feature for idle relearn, try it.

Dear sir/madam,
May you be healthy,
this is the car details: Nissan skyline, gasoline, direct injector, six cylinder, engine VQ25 (DD)
we went to this work support section and then we press enter
and the following text appeared
fuel pump will stop by touching start in idling crank a few times after engine stall
condition setting
fuel pump relay : off
so the main problem is that when we start the car and the engine speed does not go on from 1000 R/PM and the car become off
so what should we do?
And we checked the car by carman scan lite
please kindly explain it in details
Thank you in advance

please kindly explain it again , and the trouble is that when we start the car and it on and after 3 second it become stop or off

The work support you mentioned is for testing different components.
You need to check why the fuel pump is stopping after 3 seconds. Check for trouble codes. A sensor could be faulty or not properly plugged in.

Ensure the Mass Air Flow Sensor is good and there are no vacuum leakages between it and the throttle body.

Dear Sir / Madam,
May you be fine and doing well,
I have a trouble with the car please kindly answer it,
when and why the below code appeared?
Po717 input /Turbine speed sensor "A" circuit no signal
please explain it in details

Dear sir/ madam,
May my email finds you well and healthy,

I confronted a trouble as bellow:
I changed the injector of the tata or xenon car, so now it can not start properly, so what should i do ?

does it need the coding if so how can i install it and follow the coding procedures?
please kindly write me the properly ways of coding and programming of the replacement of the injectors?

Thanks in advance
Faiz

injectors do not require coding.