Cylinder head torque specs

2003 FORD WINDSTAR
150,000 MILES • 3.8L • 6 CYL • 2WD • AUTOMATIC
Avatar
ROBB2K
  • MEMBER
  • 4 POSTS
I am having to change the heads on my motor and have read in different places different torque specifications and procedures. I don't have a factory service manual. I have bought new TTY long and short bolts for this car for the job. What I have seen is:

Lubrication bolts with motor oil
Tighten bolts in the correct sequence in three stages:
1. Torque to 15 ft lbs
2, Torque to 30 ft lbs
3. Torque to 37 ft lbs

Then loosen each bolt in sequence following below but one only loosen one bolt at at time:

Loosen two turns
For short bolts: torque to 18 ft lbs then 180 degrees more.
For long bolts: torque to 33 ft lbs then 180 degrees more

One manual said use RTV on the short bolts.

Engine is a 3.8 liter with aluminum heads casting YF2E

Could someone comment on the details? Little info out there and what there is conflicts with Haynes etc.
Dec 31, 2018 at 9:43 AM
Advertisement
Avatar
ASEMASTER6371
  • CERTIFIED EXPERT
  • 52,796 POSTS
Good morning,

Below is the process for torque specs.

Make sure you do the final with starting at the center out.

use clean oil on the bolts. do not use anything else.

Roy

NOTE: Lubricate the bolts with clean engine oil prior to installation.

Install the new bolts. Make sure the bolts are installed in the correct locations.
1. Install new long bolts.
2. Install new short bolts.


imageOpen In New TabZoom/Print


4. Tighten the bolts in the sequence shown in three stages.
- Stage 1: Tighten to 20 Nm (14 ft. lbs.).
- Stage 2: Tighten to 40 Nm (29 ft. lbs.).
- Stage 3: Tighten to 50 Nm (36 ft. lbs.).


imageOpen In New TabZoom/Print


5. CAUTION: Do not loosen all of the bolts at one time. Each bolt must be loosened and tightened prior to working on the next bolt in the sequence.

NOTE: The short bolts are numbered 2, 4, 6 and 8 and the long bolts are numbered 1, 3, 5 and 7.

Loosen, then tighten the bolts in the sequence shown:
- Tighten short bolts to 25 Nm (18 ft. lbs.), then tighten an additional 180 degrees.
- Tighten long bolts to 45 Nm (33 ft. lbs.), then tighten an additional 180 degrees.


imageOpen In New TabZoom/Print


6. Install the exhaust manifold lower studs.


imageOpen In New TabZoom/Print


7. NOTE: Lubricate the push rods with clean engine oil prior to installation.

Install the push rods.


image
Dec 31, 2018 at 9:58 AM
Avatar
ROBB2K
  • MEMBER
  • 4 POSTS
Thank you. Do any of the bolts need thread sealant? I am not sure if any go through water jackets.
Jan 2, 2019 at 4:15 PM
Advertisement
Avatar
ASEMASTER6371
  • CERTIFIED EXPERT
  • 52,796 POSTS
No, never use that, very rarely do some manufacturers suggest that.

Roy
Jan 2, 2019 at 4:25 PM
Avatar
ROBB2K
  • MEMBER
  • 4 POSTS
Thanks. One more detail. Could you give me the procedure/torque specs for the rocker arm bolts?
Jan 3, 2019 at 8:07 AM
Avatar
ASEMASTER6371
  • CERTIFIED EXPERT
  • 52,796 POSTS
Here you go:

1. Install the rocker arms.
- Position the rocker arms.
- Hand-start the bolts.
- Tighten the bolts in two stages.
- Stage 1: Tighten to 5 Nm (44 inch lbs.).
- Stage 2: Tighten to 32 Nm (24 ft. lbs.).
2. Install the valve cover.
Jan 3, 2019 at 8:42 AM