Transmission not working properly after overhauling the engine?

1998 MITSUBISHI CHARIOT
126,000 MILES
Avatar
MANGIPLES
  • MEMBER
  • 6 POSTS
4g64 recently overhauled engine immaculate, Previous to Auto shop works , AT working fine and shifting normal, after overhaul AT is locked in 3rd gear with neutral light indicator blinking, tried shift up or down using manual selector without luck.

1998 Mitz Chariot grandis 2.4 GDI DOHC 4g64 N84W INVECS-II four-speed semi-auto
Aug 24, 2013 at 7:05 PM
Advertisement
Avatar
JACOBANDNICKOLAS
  • CERTIFIED EXPERT
  • 110,175 POSTS
Have you checked the range sensor?
Aug 24, 2013 at 7:13 PM
Avatar
MANGIPLES
  • MEMBER
  • 6 POSTS
Is this sensor mounted on the At with 3 wires green, blue white and brown pluged into it? if so then yeas its broken.
Aug 24, 2013 at 7:35 PM
Advertisement
Avatar
JACOBANDNICKOLAS
  • CERTIFIED EXPERT
  • 110,175 POSTS
I hate to say it, but I don't have the specifics on this model. However, it would be mounted on the trans and chances are what you are looking at is the sensor.
Aug 24, 2013 at 7:46 PM
Avatar
MANGIPLES
  • MEMBER
  • 6 POSTS
mmmm same same... hard to find specs NE way its broken and should be fixed, how do you remove though it looks like plastic?
Aug 24, 2013 at 7:53 PM
Avatar
JACOBANDNICKOLAS
  • CERTIFIED EXPERT
  • 110,175 POSTS
If there is no retaining bolt holding it in place, it should just screw into place.
Aug 24, 2013 at 7:58 PM
Avatar
MANGIPLES
  • MEMBER
  • 6 POSTS
yes looks like its a screw type. Tenkz
Aug 24, 2013 at 8:08 PM
Avatar
JACOBANDNICKOLAS
  • CERTIFIED EXPERT
  • 110,175 POSTS
Keep me informed about your progress.
Aug 25, 2013 at 7:37 PM
Avatar
MANGIPLES
  • MEMBER
  • 6 POSTS
Jacobandnickolas, on same vehicle i recently had an overhaul, changed gasket and rings and coils, after vehicle omits very heavy smoke. after overhaul still smoking after engine gets hot but very light blue white colour smoke still omitts ne idea?
Sep 3, 2013 at 11:10 PM
Avatar
JACOBANDNICKOLAS
  • CERTIFIED EXPERT
  • 110,175 POSTS
White smoke usually indicates that coolant is getting into the combustion chamber. Is the vehicle using any coolant? Also, check the oil to see if there is any contamination. When you replaced the rings, did you check the end gap clearance to make sure it didn't need to be over sized? Also, was anything done with the valves or valve stem seals?
Sep 4, 2013 at 6:23 PM
Avatar
EXOMOZIBAJHOF
  • MEMBER
  • 1 POST
Uvateyo Ogexel rqf.hxnr.2carpros.com.dbj.rw http://slkjfdf.net/
Apr 18, 2023 at 10:50 PM
Avatar
IXIQSUMO
  • MEMBER
  • 0 POST
Anulid Yermunx kno.wyqg.2carpros.com.hhk.nq http://slkjfdf.net/
Apr 18, 2023 at 11:05 PM
Avatar
UCASIREPO
  • MEMBER
  • 0 POST
Enuegifw Awinugud lju.upok.2carpros.com.abh.fk http://slkjfdf.net/
Apr 18, 2023 at 11:21 PM