what would cause total electrical loss when the ignition switch is turned to start?

1992 FORD CROWN VICTORIA
200,000 MILES
Avatar
BARAY
  • MEMBER
  • 4 POSTS
The car will start sometimes, but mostly when I turn the ingition switch on there is a loud click over on the passenger side, seems like it is just inside the engine compartment; all electrical goes out, no gauges, no lights, no starter turn over, no nothing electrical; however, the battery still maintains a full charge. Usually there is a buzzing, humming, electrical vibration noise coming from the same area as the click. Seems like when the noise stops, the electrical comes back on. This sometimes takes just seconds, and sometimes minutes. I can feel the vibrations of the noise on one of the posts of the starter solenoid mounted on the wheel well on that side; it seems like it might even be coming from the wire attached to that post; it's the smaller wire, not the main battery wire. I put in a new starter solenoid and had the battery and starter tested ~ both good.
Oct 4, 2011 at 2:41 PM
Advertisement
Avatar
JACOBANDNICKOLAS
  • CERTIFIED EXPERT
  • 110,175 POSTS
Remove, clean, and properly tighten the battery terminals. Make sure the terminals are clean and tight on the solenoid too. It sounds like a battery terminal that isn't making a good connection.
Oct 4, 2011 at 2:46 PM
Avatar
BARAY
  • MEMBER
  • 4 POSTS
Thank you for your reply; one of the first things I did but it didn't fix the problem.
Oct 4, 2011 at 2:51 PM
Advertisement
Avatar
JACOBANDNICKOLAS
  • CERTIFIED EXPERT
  • 110,175 POSTS
Did you check the ground to the engine block?
Oct 4, 2011 at 4:33 PM
Avatar
BARAY
  • MEMBER
  • 4 POSTS
I haven't specifically checked the actual connection, but a volt meter on the + side of the battery and the ground side connected to the engine block shows the battery voltage without fluctuation. I'll check the actual connection when I get to where the car is later this afternoon. Thanks.
Oct 4, 2011 at 5:42 PM
Avatar
JACOBANDNICKOLAS
  • CERTIFIED EXPERT
  • 110,175 POSTS
Let me know what you find.
Oct 8, 2011 at 5:57 PM
Avatar
CADIEMAN
  • CERTIFIED EXPERT
  • 3,544 POSTS
you need a multi meter to read the voltage at the starter whyll cranking.try tapping the starter with a hammer whyll cranking.
Oct 8, 2011 at 6:19 PM
Avatar
CADIEMAN
  • CERTIFIED EXPERT
  • 3,544 POSTS
make sure the small wire is going to the s terminal on the seloniod.
Oct 8, 2011 at 6:39 PM
Avatar
CJ MEDEVAC
  • CERTIFIED EXPERT
  • 11,004 POSTS
CHECK YOUR FUSES!!!---YOUR OWNERS MANUAL MAY SHOW YOU LOCATIONS THAT YOU KNEW NOTHING ABOUT! REMOVE AND REPLACE "SUSPECT" FUSES SEVERAL TIMES--THIS MAY SCRAPE OFF CORROSION AND GIVE THEM BETTER CONTACT!

THIS WILL WORK FOR YOU, PROVIDED THAT YOUR BATTERY IS GOOD---OR YOU CAN BE JUMPED OFF!!!

REMEMBER "NEW STUFF" CAN BE BAD TOO!

YOUR STARTER MAY BE BAD! YOUR SOLENOID MAY BE BAD! Try the stuff below (actions)

TAKE STUFF LOOSE-----CLEAN-----"SCOOCH IT AROUND TO OBTAIN BETTER CONTACT.....THEN TIGHTEN NUTS AND BOLTS WELL-----DO NOT JUST PASS ANYTHING OFF AS,........."IT LOOKS GOOD", OR "THAT LOOKS TIGHT".

JUST A LITTLE MORE ATTENTION AS YOU GO, MAY SAVE YOU A HECK OF A LOT OF TIME AND $$$!

Do not leave off where the Battery cables connect to the Battery clamps! (not the posts, the "squeeze connections" on the cables) While you are at it, Both ends of Pos cable, Both ends of NEG cable. If you still have the problem. Follow Battery Positive cable to find the Solenoid. Clean it's connections.

Clean and tighten the starter connections too!

ALL IN ALL, EVERY CONNECTION, FROM THE BATTERY, UNTIL IT ENDS MUST BE CHECKED!

Usually a situation like yours is a cable connection, next step after this will be to find and check fusible links....they will sometimes burn up, ESPECIALLY if jumper cables were installed wrong!

KEEP US INFORMED....I'M PULLIN' FOR YOU!

THE MEDIC
Oct 8, 2011 at 6:46 PM
Avatar
BARAY
  • MEMBER
  • 4 POSTS
Thank you all for your input; checked everything, replaced the battery clamps and cleaned the cables on both the positive and negative cables. Started right up, seems to be running okay now. Negative battery cable where it attached to clamp seemed to be very corroded, I will be replacing it. Again, thanks.
Oct 10, 2011 at 12:55 PM
Avatar
CADIEMAN
  • CERTIFIED EXPERT
  • 3,544 POSTS
np ty for using 2cafrpros
Oct 10, 2011 at 4:36 PM
Avatar
JACOBANDNICKOLAS
  • CERTIFIED EXPERT
  • 110,175 POSTS
That was the first thing I mentioned. That is one of the most common problems. Glad you got it fixed.
Oct 10, 2011 at 5:21 PM
Avatar
CADIEMAN
  • CERTIFIED EXPERT
  • 3,544 POSTS
i said that to jacobandnickolas.good one
Oct 10, 2011 at 7:01 PM